Watch the lesson
Support and Resistance Zones Explained: ATR-Sized Zones on TradingView (9:05). Also on the free lessons page, with chapters. Education only, not a trade signal or personal advice.
Why zones instead of lines
Look closely at most swing highs: one candle wicks a little above, another stops a little below. A single line is wrong by a few pips every time. A zone, or area of interest, says "this region matters; watch what price does when it gets there". It's a location, not an instruction to buy or sell.
Step 1: Find the latest swing high and swing low
- A swing high is a candle whose high is higher than the seven candles before it and the seven after it. A swing low is the mirror image.
- Seven is a starting point: a smaller number picks up every wiggle; a larger one gives fewer, more significant swings.
- Use only the latest swing high and the latest swing low. Two zones keep the chart clean.
A swing is only confirmed once those seven candles have printed on the right, so it's always a little old. That delay is the price of not repainting.
Step 2: Size the zone with ATR
ATR (average true range) is the average size of a candle's range, usually over 14 candles. Multiply it by 0.4 and draw the zone that distance above and below the swing's extreme.
Worked example (made-up numbers): ATR = 10 pips, so 0.4 × ATR = 4 pips. The zone runs 4 pips above and 4 pips below the swing high: 8 pips tall in total. On busier days the zone widens, and on quieter days it tightens, so you don't have to keep adjusting a fixed pip distance.
Step 3: Count the touches
Look back around 200 candles and count every candle whose range overlaps the zone, even with just a wick. More touches can mean an area has been noticed; it can also mean it's being worn down. Note that the swing candle and its neighbors count too, so a new zone doesn't start at zero. Use touch counts to compare your two zones, not to predict anything.
Step 4: Check for compression
Measure the gap between the bottom of the upper zone and the top of the lower zone. If it's less than one ATR, price is squeezed between two nearby areas with little room to move before meeting one of them. If the zones overlap, the gap is zero or negative. Either mark both zones as a warning or keep only the one with more touches, and don't read a tight squeeze as two separate opportunities.
Step 5: When price reaches a zone
A zone touch isn't an entry; it's the moment to start paying attention. Watch how candles behave: does a candle wick in and close back out, does the next candle confirm it, or does price close straight through? Zones break, and the clean-looking ones always look cleaner in hindsight.
Trading the 5- or 15-minute chart? The Hourly Zones indicator draws one support and one resistance zone from closed 1-hour swings, sized by 1-hour ATR, with 1-hour touch counts and compression control.
Frequently asked questions
How wide should a support and resistance zone be?
One volatility-based approach is the swing's extreme plus and minus 0.4 × ATR(14). The zone then widens on busy days and tightens on quiet ones.
What counts as a swing high?
Here, a candle whose high is above the seven candles before and after it. You can use a different number; smaller finds more swings, larger finds fewer.
Do more touches make a zone stronger?
Not necessarily. More touches can mean an area has been noticed, or that it's being worn down. Use touches to compare zones, not to predict whether one holds.
What is compression between zones?
When the gap between the upper and lower zones is less than one ATR, or they overlap. Price has little room before meeting one of them.
Is touching a zone a reason to enter a trade?
No. A zone is a location to watch. What candles do there, and your own plan and risk, matter more. This guide is education only.
Related guides
MACD histogram colors explained: the four shades, zero crosses and the 4H ATR
Deep teal, pale teal, pale red, deep red: what each shade says about momentum, plus how a 4-hour ATR reading fits alongside it.
Multi-timeframe bias: how to read trend across timeframes
Two questions per timeframe, an overall count, and the six ways a bias table can mislead you.
Related tools
Zone Map
Clean Support & Resistance
Smart MACD
Momentum + Volatility Dashboard
Free Trend Check Dashboard
Multi-Timeframe Bullish / Bearish Table
Based on our free video lesson. Examples use made-up numbers to explain the arithmetic. Questions? Email contact@brainiosoftware.com or see the FAQ.
General information only. These guides explain how TradingView features work. They are general education, not personal financial product advice or a recommendation. Screener results and indicator readings are not trade signals. TradingView is a third-party platform and changes its features over time; we are not affiliated with or endorsed by TradingView. Read the full risk disclaimer.