Watch the lesson
Drawing Clean Support & Resistance Zones (AOI) the Simple Way (8:29). Also on the free lessons page, with chapters. Education only. The video explains how the rules work; it is not personal advice.
Two ways to build a zone automatically
| Method | How the zone is found | Strength | Weakness |
|---|---|---|---|
| Base detection | Look for a few small candles followed by a large departure candle; box the base | Close to the classic supply/demand idea | Many parameters (what counts as "small" and "large"), so results vary a lot by setting |
| Swing zones | Take the latest confirmed swing high and swing low and draw a zone around each | Simple, consistent, few settings | Shows the most recent zones rather than every historic base |
Neither is "correct". Base detection suits traders who think in departures and freshness; swing zones suit traders who want one support and one resistance area to plan around. The manual version of the base method is in how to draw supply and demand zones.
Sizing: why ATR
A zone drawn from a candle's body to its wick can be tiny on a quiet day and enormous after news. Sizing the zone as a multiple of ATR keeps it in proportion to how far the market normally moves.
Worked example. AUDUSD 1-hour, ATR(14) = 18 pips. A confirmed swing low prints at 0.6542. With a zone half-height of 0.40 x ATR (7.2 pips), the support zone runs from about 0.6535 to 0.6549. If ATR doubles to 36 pips after a data release, the next zone drawn is twice as tall, which matches the wider swings.
Freshness and touch counts
Supply/demand traders care whether a zone is fresh. Indicators approximate this with a touch count: how many candles (or separate visits) traded inside the zone over a lookback, such as the last 200 candles. A zone with 2 touches and one with 14 describe very different histories. More touches can mean a well-respected area, or one that has been worn down; the count gives you the fact, and you decide how to read it.
When zones crowd together
In a tight range, the support and resistance zones can overlap. A good indicator handles this explicitly, either by hiding the weaker zone (fewer touches) or by coloring both to show compression. Two overlapping zones aren't two separate opportunities; they're one congested area.
Settings to start with
- Pivot length: 5 to 7 on 1-hour and 4-hour charts.
- ATR length: 14.
- Zone height: about 0.40 x ATR as a starting point; raise it on noisy markets.
- Touch lookback: 200 candles.
- Compression mode: hide the weaker zone if you want a clean chart; color both if you want to see the congestion.
Apex Edge Zone Map uses the swing method: one resistance and one support zone from the latest confirmed swings, height as a multiple of ATR (0.40 x ATR by default), touch counts over the last 200 candles, a compression mode and zone-entry alerts. It is not a base detector, so if you work strictly from bases and departures, pair it with your own drawing.
Common mistakes
- Too many zones. If the chart has eight zones, price is always "at a zone".
- Ignoring the confirmation delay. Swing-based zones appear after the pivot confirms. That's by design.
- Treating a zone as a line that must hold. Zones are areas; price often trades through part of them.
- No trend context. A demand zone inside a clean downtrend is a weaker read than one aligned with the higher timeframe.
Tools for this guide: Apex Edge Zone Map. For a free starting point, the Free Trend Check Dashboard shows trend bias across ten timeframes: claim it free with your email.
Frequently asked questions
Is there a supply and demand indicator on TradingView?
Yes, there are many community scripts. Check whether each one uses base detection or swing zones, how it sizes zones, and whether it waits for confirmation.
How big should a supply and demand zone be?
A common approach is a multiple of ATR, such as a half-height of 0.40 x ATR, so zones scale with volatility.
What is a fresh zone?
A zone price hasn't returned to since it formed. Indicators approximate freshness with a touch count over a lookback.
Are supply and demand zones the same as support and resistance?
They overlap. Supply/demand usually focuses on bases before strong moves; support/resistance on levels price has reacted to repeatedly.
Why did my zone move?
Swing-based zones update when a new swing is confirmed. If a zone moves without a new confirmed swing, the indicator may be redrawing.
Keep reading
Support and resistance indicators on TradingView compared
Six types of support and resistance indicator on TradingView compared: pivot points, prior-day levels, swing lines, ATR zones, volume profile and more.
Fair value gap indicator for TradingView: how it works and what to set
How a fair value gap indicator on TradingView finds three-candle imbalances, tracks fill status and filters small gaps, with settings and common mistakes.
Market structure indicator for TradingView: swings, breaks and shifts
What a market structure indicator on TradingView labels: confirmed swings, HH/HL/LH/LL, breaks and character shifts, plus pivot settings and mistakes.
More in Support, resistance and supply/demand zones, or browse all guides by topic. Questions? Email contact@brainiosoftware.com.
General information only. This guide is general education, not personal financial product advice or a recommendation to buy or sell anything. Indicator readings, alerts and screener results are not trade recommendations. Examples use illustrative numbers. TradingView is a third-party platform; we are not affiliated with or endorsed by TradingView. Education only. Not financial advice. Trading involves risk of loss. Read the full risk disclaimer.